Most of the parts available on my website require advanced skill to install on your build. Fabrication or modification of them may be required due to the broad range of applications to which they are suited. Be sure to use appropriate protection when working with tools or chemicals which represent a potential threat to your personal well-being.

Tips for dealing with photo etch -
removal from rubber backing: Soak light-weight or fragile pieces in acetone until the part separates from the rubber backing. For heavier parts that have no etch lines or thin edges where there is a likelihood of damage, you may be able to peel the rubber off before soaking in acetone. It works best to fold the rubber back against itself as you peel it back to lessen the likelihood being parts.

1/25th Scale

C-BEZ-OH-2  Oval Header Bezels  $1.60
These bezels are the perfect way to finish the fender exit holes on your high-powered doorslammer build.  They are especially well-suited if headers exit at an angle.  As-drawn inside dimensions are .2515" x .2194".  Outside dimensions are .3007" x .2623".  They are etched out of .004" stainless steel.
 




C-BEZ-RH-2  Round Header Bezels  $1.50
These bezels are the perfect way to finish the fender exit holes on your doorslammer build if the headers exit perpendicular to the body.  As-drawn inside dimensions are .2199" x .2199".  Outside dimensions are .2498" x .2714".  They are etched out of .004" stainless steel.
  



C-BEZ-WI-4 Doorslammer Window Bezels  $1.50

These window bezels are intended to add a finished look to the emergency access hole that is required in many doorslammer cars so track personnel can reach through a window to open the door in case of an emergency.  As-drawn inside dimensions are .1626" x .1626".  Outside dimensions are .1846" x .2006".  They are etched out of .004" stainless steel.  Enough to finish two cars. 




C-DCL-S Door Car Levers  $3.00
These levers are etched out of .006" nickel-silver and are intended to replicate interior levers, such as those used for interior door releases, parachute release, etc.  Enough pieces to finish two cars.



C-DZB-S Dzus Button Set  $3.00                                                                                                                                                           These self-ejecting Dzus buttons replicate the quarter-turn fasteners used on all manner of race cars, especially on panels that require simple, quick removal for between-rounds maintenance.  Etched out of .004" stainless steel.  Eighty-four pieces are included Etched out of .004" stainless steel.  Eighty-four pieces are included in this set.


Dzus Mounting Plate w/Hexagonal End  $4.00
These mounting plates are photo-etched out of .006" nickel-silver plate.  Plate is hexagonal in shape on one end. 




C-DZP-LS Dzus Mounting Plate, Lightweight  $3.00 
These mounting plates are photo-etched out of .006 nickel-silver plate.  Plates replicate a swiss cheese design of Dzus plates.  This style is used a lot on current race cars and add great realism to your build.



C-DZP-SS Dzus Mounting Plate, Standard  $3.00 
These mounting plates are photo-etched out of .006 nickel-silver plate.  Plates replicate a basic design of Dzus plates.  This style was used a lot on race cars back in the 70s and 80s and adds great realism to your build. 



C-FRK-1F Frame Rail Kit, 2x3 Mandrel Bent  $8.00
These frame rails are available in Shapeways' 3D-printed FUD (frosted ultra detail).  They come with separate .060" diameter styrene cross members and are 2.6 inches in length.  The rail dimensions are .125" x .080".   



C-FTA-S Foldable Chassis Tab Set  $7.00
These foldable tabs allow you to mount suspension components in a more secure way.  The suspension is sandwiched between the folded sides of the brackets. They are designed to work with .080” OD chassis tubing. Holes may need to be drilled out to accept mounting bolts/hardware.
 



C-FTA-063/080S Foldable Chassis Tab Set for .063/.080  $8.50
This foldable tab set is the same as the FTA-S set other than the tabs are a mix to fit .063" (34 pcs) and .080" (21 pcs) OD chassis tubing.  Holes may need to be drilled out to accept mounting bolts/hardware.



C-HAR-CL-2 Cam-Lock 5-Way Racing Harness  $8.00
These 1/25th scale photo etch sets replicate a more contemporary style of hardware used by many race cars today.
  Etched out of .006" nickel silver, these require patience and dexterity when assembling, but the results are worth it!



C-HAR-LL-2 Lever Latch 5-Way Racing Harness  $8.00
The origins of this style of racing harness hardware dates back to WWII.  It is still available and widely in use today.  These 1/25th scale sets replicate the basic style of hardware used by many race and street cars, even today.  Assembly, patience and dexterity required!



C-LEV-2 Hand Brake and Lever Kit  $3.00
This is my original design of hand brake and miscellaneous levers.  They are of a more simple design and may be better suited for older styles of builds.  The smaller levers can be used for parachute releases, fuel shut-offs, or what-have-you.  they are etched out of .010" nickel-silver.



C-LEV-2N Hand Brake and Lever Kit, New Design  $4.00
This set of hand brakes and levers are a contemporary design.  They are more stylish and there are two sizes of the smaller levers, which adds versatility and variety to a cockpit.  The hand brake levers also include separate add-on grips if you wish to add a bit more 3-dimensionality to the levers or want the levers a different color to stand out.  As with my other levers, these are etched out of .010" nickel-silver.



C-PED-2 Clutch, Brake, Accelerator Pedal Kit (2)  $4.00
This set of photo-etched pedals is enough to build two cars.  Clutch, brake and accelerator pedals arms include separate non-slip pedal pads.
 




C-ROT-DR2F Drilled Rotor and Brake Set, Front  $5.00
This drilled rotor set is designed to work with .093" spindle diameter and allows the use of separate calipers and PE brackets.  Includes PE rotors, caliper brackets and steering arms, resin hubs/spacers and calipers.



C-ROT-DR2R Drilled Rotor and Brake Set, Rear  $5.00
This drilled rotor set is designed to work with .0625" axle diameter and allows the use of separate calipers and PE brackets, for more realism.  Includes PE rotors, calipers brackets and axle housing flanges; resin hats and calipers.



C-ROT-SL4 Retrofit Slotted Rotors  $6.00
These rotors come as a set of four and can be used as direct replacements on any of my 1/25th scale drilled rotors included in the strut front end kit, the drilled rotor sets, above, or any of my rear end housing kits.



C-RTF-700 Round Tube Frame, Small - FUD Material $8.00
This round tube frame rail set is .700" wide and is intended for use in small, short wheelbase, narrow body styles. The main rails are .080" in diameter with .063" round cross members and are 3D-printed in Shapeways' FUD (Frosted Ultra Detail) material. Approximately 2.7" long. The FUD material will require very little effort to prep it for finishing. It can be soaked in acetone for a few minutes to remove residual contamination from the printing process. This chassis is designed to use a custom photo etch 4-link set that was developed for this specific application. The 4-link set is S-4LFK-1 and is available separately.
 



C-RTF-800 Round Tube Frame, Medium - FUD Material  $8.00
This round tube frame rail set is .800" wide and is intended for use in small, intermediate body styles. The main rails are .080" in diameter with .063" round cross members and are 3D-printed in Shapeways' FUD (Frosted Ultra Detail) material. Approximately 2.7" long. The FUD material will require very little effort to prep it for finishing. It can be soaked in acetone for a few minutes to remove residual contamination from the printing process. This chassis is designed to use a custom photo etch 4-link set that was developed for this specific application. The 4-link set is S-4LFK-1 and is available separately. (Shown in WSF)




C-RTF-900 Round Tube Frame, Large - FUD Material  $8.00
This round tube frame rail set is .900" wide and is intended for use in large, longer-wheelbase body styles.  The main rails are .080" diameter with .063" cross members and are 3D-printed in Shapeways' FUD (Frosted Ultra DEtail) material.  Approximately 2.85" long.  This FUD material will require very little effort to prep it for finishing.  It can be soaked in acetone for a few minutes to remove residual contamination from the printing process.  This chassis is designed to use a custom photo etch 4-link set that was developed for this specific application.  The 4-link set is S-4LFK-1 and is available separately.
  



C-SGU-1 Strut Gusset Kit  $5.00
These gussets are intended to add both structural support as well as added detail to the upper strut mount on your build.  Etched out of .010" nickel-silver, there are enough for approximately seven cars.  These gussets are intended to fit around a 3/32 (.094)" upper strut mount.
 



C-TAB-063S Tab and Bracket Assortment for .063" Tubing  $7.00
These tabs are intended to be used with .063" diameter tubing.  As can be seen, there is a variety of tabs, many of which are very small, so be sure to have good lighting, magnifier and patience!



C-TAB-080S Tab and Bracket Assortment for .080" Tubing  $7.50
This set of tabs is identical to the ones above, but are intended  to be used with .080" diameter tubing.  The same patience, good lighting and magnification applies for these tabs, too...




C-WBK-M1 Wheelie Bar Housing Kit  $6.00
This wheelie bar housing kit allows the builder to use whatever material and length of tubing that is preferred for the tubular structure.  When housing sides are folded up, the space between the inside edges of the housing is ~.035".  Not shown in this picture is I have begun including 3D-printed discs that may be used in place of the 3-piece wheels, if desired.  The discs are intended to replace the entire PE wheel system.



R-9IN-1KN Narrowed OEM 9-Inch Ford Rear End Kit w/Brakes  $13.50
One piece OEM-style 9-inch Ford rear with back brace, center section, resin calipers and hats, plus PE caliper mounts, axle housing ends (one spare) and drilled rotors.  Housing includes cast-in-place .063" aluminum tube core.  The corresponding 4-link set for this rear end is S-4L9B-1.  Caliper bracket instructions included.



R-DAN-1K Narrowed Dana 60 Rear End Housing Kit w/Brakes  $13.50
One piece, narrowed Dana 60 housing.  Housing has cast-in-place .063" aluminum tube core.  Includes rear cover, resin calipers and hats, plus PE caliper mounts, axle housing ends (plus spare) and drilled rotors.  As-cast, bare axle housing dimension is ~1.60".  The corresponding 4-link set for this rear end is S-4LPM-1.  Caliper instructions included.



R-FAB9-1K Narrowed, Fabricated 9-Inch Ford Rear End Housing Kit w/Brakes  $13.50
One piece, fabricated 9-inch Ford rear with back brace, center section, resin calipers and hats, plus PE caliper mounts (one spare), axle housing ends and drilled rotors.  Housing includes fill cap and drain plug.  Housing has cast-in-place .063" aluminum tube core.  The corresponding 4-link set for this rear end is S-4LF9-1.  Caliper instructions included.



S-4L9B-1 OEM-9-Inch Rear End 4-Link Housing Kit  $14.00
Contemporary 4-link multi-media kit fits one-piece R-9IN-1KN housing.  Kit includes chassis and rear end housing brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes, cut to ~.750" length and eight formed-wire rod ends.  Effective May, 2015, I am going to include formed-wire rod ends that will need to be trimmed on the end opposite the eye.



S-4L9BP-1  Braced Ford 9-Inch 4-Link Housing Kit for Fairmont/Zephyr Pan  $14.00
Contemporary 4-link multi-media kit fits one-piece R-9IN-1KN housing and Fairmont/Zephyr pan, B-PAN-1.  Kit includes chassis and rear end brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubs, cut to ~.750" length and eight formed-wire rod ends.  Effective May, 2015, I am going to include formed-wire rods ends that will need to be trimmed on the end opposite the eye.
Photo soon!



S-4LF9-1 Braced Fabricated Ford 9-Inch 4-Link Housing Kit  $14.00
Contemporary 4-link multi-media kit fits one-piece $-FAB9-1K housing.  Kit includes chassis and rear end housing brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes, cut to ~.750" length and eight formed-wire rod ends.  Effective May, 2015, I am going to include formed-wire rod ends that will need to be trimmed on the end opposite the eye.



S-4LFK-1 Braced OEM Ford 9-Inch  4-Link Housing Kit (fits RTF- and FRK- Series Frame Kits  $14.00
Contemporary 4-link multi-media kit fits narrowed OEM-style 9-inch Ford housing.  Kit includes chassis and rear end housing brackets, etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes, to ~.750" length and eight formed-wire rod ends.  Designed to fit RTF (round tube frame) and FRK (mandrel bent frame rail kits).  Effective May, 2015, I am going to include formed-wire rod ends that will need to be trimmed on the end opposite the eye.




S-4LPM-1 Pro Mod 4-Link Housing Kit  $14.00
Contemporary 4-link multi-media kit fits rear ends with .125" OD axle housing with no back brace.  Kit includes chassis and rear end housing brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes, cut to ~.750" length and eight formed-wire rod ends.  Effective May, 2015, I am going to include formed wire rod ends that will need to be trimmed on the end opposite the eye.




S-4LPT-1 Pro Touring 4-Link Housing Kit  $14.00
This 4-link multi-media kit replicates a lower stance, with the upper axle housing 4-link bar being much closer to the axle.  Mounts on lower, front portion of axle housing.  Kit includes chassis and rear end housing brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes cut to ~.750" length, eight formed-wire rod ends, Watts linkage and a variety of chassis-side brackets.  Fabrication and assembly required.  Effective May, 2015, I am going to include formed-wire rod ends that will need to be trimmed on the end opposite the eye.



S-4LRE-1 Revell Retrofit 4-Link Housing Kit  Out of Stock!
This 4-link multi-media kit replaces the styrene 4-link in the Revell top sportsman kit.  Fits Revell kit rear end or rear ends with .125" OD housing with no back brace.  Kit includes chassis and rear end housing brackets etched out of .010" nickel-silver plate, four .050" OD stainless steel tubes, cut to ~.750" length and eight formed-wire rod ends.  Effective May, 2015, I am going to include formed-wire rod ends that will need to be trimmed on the end opposite the eye.
 


S-COS-1 Coil-Over Shock Kit  $11.00
This coil-over shock kit consists of 20 pieces, 10 per side.  I have changed over to 3D-printed, 2-piece coil-over bodies.  These pictures are of the original design.  an assembled kit makes for a very realistic appearing coil-over!
Coil-over assembly instructions.

 



S-SPF-2 Suspension Spring, .250" Length x .125" OD (2)  $2.00/pr
These springs are used on my strut front end kits but would be perfectly at home on any suspension system that requires the dimensions noted above.  The ends are ground flat.  Wire diameter is .016".
 



S-SPR-2 Suspension Spring, .375" Length x .125" OD (2)  $2.00/pr
These springs are used on my coil-over rear end kit but may lend themselves to any suspension system that requires the dimensions noted above.  The ends are ground flat.  Wire diameter is .016".



S-SFE-1 Strut Front End Kit  $17.00
This strut front end kit consists of 28 pieces and includes PE caliper brackets, drilled rotors and steering arms.  It also includes 3D-printed strut bodies/spindles (resin version shown in pic) and resin brake calipers.  Springs are .125" OD and .250" long.  .033" stainless tubing is used to simulate piston rod shafts.  Assembly instructions.
 



S-STM-4 Shock Tower Mount Kit for 1966 AMT/Ertl Fairlane  $1.50/set
These upper shock mounts are made to add detail to the shock towers of AMT's 1966 Fairlane kits, which do not include these.  These mounts were cast from a mold taken from a vintage 1967 Fairlane annual kit.




S-WIB-1 Wishbone Kit, A-Arm  $1.50
This kit includes one pair of wishbones etched from .010" nickel-silver.  It will fit inside 1/16th K&S tubing or stainless steel tubing with an ID of .033".  Two separate thicknesses of washers are included - two .010" and four .015" spacers.  The spacers have flats etched into two edges to match with the angles of the wishbones.  If used with .042" OD tubing, you can sandwich the wishbone with one .015" washer on either side to build it out .042".  If using 1/16th inch K&S tubing, you can add a .010" and .015" washer on both sides of the wishbone to increase its thickness to match the 1/16th OD.